How to install OSM on VirtualBox - Revision history

Ramonsalguer at 13:49, 29 September 2021

2021-09-29T13:49:56Z

← Older revision		Revision as of 13:49, 29 September 2021
Line 1:		Line 1:
			'''Deprecated:''' Please refer to https://osm.etsi.org/docs/user-guide/

			---

	VirtualBox has different networking setup modes (see [https://www.virtualbox.org/manual/ch06.html Table 6.1])		VirtualBox has different networking setup modes (see [https://www.virtualbox.org/manual/ch06.html Table 6.1])

Fraiadan at 10:41, 21 September 2018

2018-09-21T10:41:43Z

← Older revision		Revision as of 10:41, 21 September 2018
Line 24:		Line 24:
	5) Restart the network services, then the VM should be reachable in ssh from the host using the static IP address		5) Restart the network services, then the VM should be reachable in ssh from the host using the static IP address
	sudo service networking restart		sudo service networking restart
	6) Configure LXD following the instructions: [https://osm.etsi.org/wikipub/index.php/~~LXD_configuration_for_OSM_Release_THRE~~ OSM Release THREE LXD config]		6) Configure LXD following the instructions: [https://osm.etsi.org/wikipub/index.php/LXD_configuration_for_OSM_Release_THREE OSM Release THREE LXD config]

	7) Install OSM following the instructions: [https://osm.etsi.org/wikipub/index.php/OSM_Release_THREE OSM Three install]		7) Install OSM following the instructions: [https://osm.etsi.org/wikipub/index.php/OSM_Release_THREE OSM Three install]

Fraiadan at 07:33, 10 May 2018

2018-05-10T07:33:53Z

← Older revision		Revision as of 07:33, 10 May 2018
Line 11:		Line 11:
	2) Configure network with 2 adapters: NAT + Host-Only		2) Configure network with 2 adapters: NAT + Host-Only

	3) ~~Complete OSM installation following instructions here:~~		3) Install OpenSSH server (sudo apt-get install openssh-server) and update Ubuntu (sudo apt-get update)

	4) Add a static address to the "Host-only" adapter (e.g. enp0s8 with static IP 10.20.0.90), e.g. appending the following to "/etc/network/interfaces":		4) Add a static address to the "Host-only" adapter (e.g. enp0s8 with static IP 10.20.0.90), e.g. appending the following to "/etc/network/interfaces":
Line 22:		Line 22:
	broadcast 10.20.0.255		broadcast 10.20.0.255

	5) Restart the network services		5) Restart the network services, then the VM should be reachable in ssh from the host using the static IP address
	sudo service networking restart		sudo service networking restart
	6) Configure LXD following the instructions: [https://osm.etsi.org/wikipub/index.php/LXD_configuration_for_OSM_Release_THRE OSM Release THREE LXD config]		6) Configure LXD following the instructions: [https://osm.etsi.org/wikipub/index.php/LXD_configuration_for_OSM_Release_THRE OSM Release THREE LXD config]

Garciadeblas at 12:13, 16 April 2018

2018-04-16T12:13:31Z

@@ Line 1: / Line 1: @@
 VirtualBox has different networking setup modes (see [https://www.virtualbox.org/manual/ch06.html Table 6.1])
 In case we want to install OSM on VirtualBox, it needs an IP address that remains the same across reboots.
 If the host is attached to DHCP and you cannot access the router to assign the same IP to your VMs, "bridged" mode could be difficult to manage. So, a possible alternative is to have two network adapters: one NAT that allows the VMs to access Internet + one Host-Only that allows static address on the VM and traffic from Host to VM.
-OSM can be configured like that using the procedure below, tested on OSM r3.
+OSM can be configured like that using the procedure below, tested on OSM Rel THREE.
-./install_osm.sh
+) Create a VM on VirtualBox (e.g. 8GB RAM, 40GB DISK)
-) when the installation is over, a final step to configure NAT
+) Configure network with 2 adapters: NAT + Host-Only
-git clone https://osm.etsi.org/gerrit/osm/devops.git temp
+) Complete OSM installation following instructions here:
-vi temp/installers/export_ips
+) Add a static address to the "Host-only" adapter (e.g. enp0s8 with static IP 10.20.0.90), e.g. appending the following to "/etc/network/interfaces":
-''change the DEFAULT_IF to DEFAULT_IF=enp0s8 (the interface used for Host-only network configuration)''
+ auto enp0s8
-''apply NAT rules launching '' sudo ./temp/installers/nat_osm
+) Restart the network services
-''check the rules with '' more /etc/iptables/rules.v4
+) Install OSM following the instructions: [https://osm.etsi.org/wikipub/index.php/OSM_Release_THREE OSM Three install]
-''rules are ok even after reboot, but give it some time for the VM to start (1-2 mins)''
+) Install OSM
-) access OSM using https://10.20.0.90:8443 admin/admin or ssh ubuntu@10.20.0.90
+) Access OSM GUI using https://10.20.0.90:8443 (admin/admin). You can also ssh to the Virtualbox VM running OSM (ssh ubuntu@10.20.0.90)

Fraiadan at 09:10, 16 April 2018

2018-04-16T09:10:46Z

← Older revision		Revision as of 09:10, 16 April 2018
Line 1:		Line 1:
	== How to setup OSM on VirtualBox ==		== How to setup OSM on VirtualBox (and access UI from the host without SSH tunnelling)==

	----		----

Fraiadan: How to setup OSM on VirtualBox

2018-04-16T09:08:46Z

How to setup OSM on VirtualBox

New page

== How to setup OSM on VirtualBox ==

----

VirtualBox has different networking setup modes (see [https://www.virtualbox.org/manual/ch06.html Table 6.1])

In case we want to install OSM on VirtualBox, it needs an IP address that remains the same across reboots.
If the host is attached to DHCP and you cannot access the router to assign the same IP to your VMs, "bridged" mode could be difficult to manage. So, a possible alternative is to have two network adapters: one NAT that allows the VMs to access Internet + one Host-Only that allows static address on the VM and traffic from Host to VM.

OSM can be configured like that using the procedure below, tested on OSM r3.

1) create a VM on VirtualBox (e.g. 8GB RAM, 40GB DISK)

2) configure network with 2 adapters: NAT + Host-Only

3) complete installation and add a static address to the "Host-only" adapter (e.g. enp0s8 with static IP 10.20.0.90) and have something like this:

''append this part to '' (/etc/network/interfaces)

auto enp0s8

iface enp0s8 inet static

address 10.20.0.90

netmask 255.255.255.0

network 10.20.0.0

broadcast 10.20.0.255

''then restart the network services'' (sudo service networking restart)

4) update Ubuntu and install OpenSSH to allow remote ssh access

sudo apt-get update

sudo apt-get install -y openssh-server curl wget git

5) configure LXD (from the official guide [https://osm.etsi.org/wikipub/index.php/LXD_configuration_for_OSM_Release_THRE OSM Release THREE LXD config])

sudo apt-get install -y lxd

newgrp lxd

sudo lxd init (all default but NO IPv6)

lxc list

sudo lxc profile device set default eth0 mtu 1446

6) download OSM install script, but wait to launch it! (from the official guide [https://osm.etsi.org/wikipub/index.php/OSM_Release_THREE OSM Three install])

wget https://osm-download.etsi.org/ftp/osm-3.0-three/install_osm.sh

chmod +x install_osm.sh

7) before launching the installation, modify install_osm.sh:

''find export_ips (2 times!), and add a line afterwards with ''

export DEFAULT_IP=10.20.0.90

''(it is the static IP used for host-only network)''

8) install OSM

./install_osm.sh

9) when the installation is over, a final step to configure NAT

git clone https://osm.etsi.org/gerrit/osm/devops.git temp

vi temp/installers/export_ips

''change the DEFAULT_IF to DEFAULT_IF=enp0s8 (the interface used for Host-only network configuration)''

''apply NAT rules launching '' sudo ./temp/installers/nat_osm

''check the rules with '' more /etc/iptables/rules.v4

''rules are ok even after reboot, but give it some time for the VM to start (1-2 mins)''

10) access OSM using https://10.20.0.90:8443 admin/admin or ssh ubuntu@10.20.0.90